Welcome to our world exploring the Historical, Political and Technological aspects of Locks, Keys and Safes

Results 1 to 7 of 7
  1. #1
    Join Date
    Dec 2009
    Posts
    1,496
    Country: United States

    Default Key In Knob (KIK) different/similar standards?

    I have noticed a trend in my small collection of KIK (Key In Knob) cylinders. About half are 5/8" (.625") in diameter plus or minus a few thousandths, the other half are 16 mm (.630") in diameter plus or minus maybe a tenth of a millimeter. I'm surprised the industry would support two different standards that are so close.

    This reared its ugly head when I tried to put an Assa Twin cylinder into an Abus 83/45 and it would not fit.

    Am I correct, these two sizes are distinct and exist in parallel? Did Abus make a mistake by boring the lock body for 5/8" rather than 16 mm?

    Suggestions on how to enlarge the 83/45's "pocket" are welcome, as well.

  2. #2
    Join Date
    Aug 2013
    Posts
    1,785
    Country: Wales

    Default

    Are these the binocular shaped KIK as I'm more familiar with the re-keyable Euro stuff cut for half euro cylinders, all of which is metric. I recall some padlocks we had removable USA pattern core cylinders but weren't the binocular profile.

    Assuming it's the binocular shape but either way I'd definitely hold in the 4 jaw chuck and bore out with a short rigid boring tool set in the toolpost.

    This way also makes setting up easy- turn a basic adapter spigot to fit the tailstock chuck one end and the existing bore of the pocket at the other. Then offer it up to the 4 jaw held from the tailstock chuck in order to present it relatively true to the chuck for setting.
    The usual fine truing around each jaw then applies to get the pocket perfectly centred for boring using the usual set-up-wobbler, centre finder, clock gauge etc.

    A rigid/beefy set-up is essential even though it's only a gnat's whisker of a skim, as it's still an interrupted cut and a slim boring bar will deflect into the pocket and make a mess.
    A thick shank stubby borer like a Pentatec is perfect for this.
    Don't forget to use packing strips/blocks under the jaws, sized to the volume of any offset metal in order to balance the chuck- it'll also prevent jaw marks all over it !

    **Update-from memory iirc, you have a milling machine wylk, so hold in milling vice or T-bolted/ clamped on co-ordinate table and a spindle mounted boring-head to take out the pocket might be more your thing. A lot more faffing to set it up though !

  3. #3
    Join Date
    Aug 2013
    Posts
    1,785
    Country: Wales

    Default

    I meant to add that I'd definitely refrain from drilling it out, whether you go the milling machine or lathe route. Even a real quality precision twist drill like Gühring will deflect slightly into the other pocket and 'spiral' its way down. Plus the tip angle means it wouldn't reach right to the bottom anyway.

    A spindle mounted solid 3 or 4 flute slot cutter of exactly the right size would probably do it too, if a boring-head is not available to hand.
    A similar end-mill might also work, but remember they are not intended to plunge cut into the work as here, they are for horizontal feed cutting around the outer edge.

  4. #4
    Join Date
    Dec 2009
    Posts
    1,496
    Country: United States

    Default

    Huw,

    Thanks for the suggestions. I used to have a big mill and big lathe, but now am reduced to a Sherline mill and lathe. I'm not sure they'd have the rigidity called for but I will think about it; setup would indeed be fussy. I've also thought about turning a steel bar into a sort of broach (undersized) and try to scrape the hole and shave it to a larger diameter; it would need to be fairly sharp.

    I agree about the drill/mill deflection. I would use either a single-point tool if the lock is chucked in the lathe, or possibly something like a Woodruff key cutter in a mill and the lock on a rotary table.

    (I'm having a problem attaching images, antique-locks keeps asking me to log in at almost every single step regardless of what I'm doing).

  5. #5
    Join Date
    Dec 2009
    Posts
    1,496
    Country: United States

    Default

    The following images show the 83/45 body and its (lopsided) binocular-shaped receptacle, a KIK adapter kit, and a typical KIK cylinder.

    Click image for larger version. 

Name:	s-l1600.jpg 
Views:	3 
Size:	137.7 KB 
ID:	24001Click image for larger version. 

Name:	10461__04011.jpg 
Views:	2 
Size:	73.4 KB 
ID:	24002Click image for larger version. 

Name:	GMS-K001-SC-26D-A2_NL.jpg 
Views:	2 
Size:	35.4 KB 
ID:	24003
    (my login problem appears to have been caused by the "remember me" checkbox being unchecked on login)

  6. #6
    Join Date
    Aug 2013
    Posts
    1,785
    Country: Wales

    Default

    Wylk ,how about using a small fly-cutter. I recall the Sherline's are small- i think very similar to the Peatol, so best holding the padlock stationary and spinning the cutter. Fly cutters are relatively easy to make but are available in all sizes and not too expensive.
    In fact i think Sherline/Peatol made them specifically for their machines.

    How about- if on mill set-up; padlock held on table (T-bolts & clamps) or milling vice, and then a mini fly-cutter either spindle mounted or held in collet/chuck to bore out the pocket.
    Or, if lathe set-up, padlock held against angle plate on carriage (same t-bolts or vice set-up), and same fly-cutter in spindle taper or chuck.
    Good luck I'm sure you'll do it !

  7. #7
    Join Date
    Aug 2013
    Posts
    1,785
    Country: Wales

    Default

    The more I've thought of this wylk you're better off just making one. All it needs is a stub of Ø1/2" steel bar with a step turned down to suit however you're holding it on the mill or lathe, chuck, collet or whatever you're using.

    The 1/2" business end then needs an Ø1/8" cross drilled hole diagonally at an angle, sized to suit an 1/8" dowel of HSS or silver steel, which once ground serves as the tool bit.

    Drill and tap a thread up the business end to suit a small socket screw to lock the tool bit in place and you're almost done.
    Grind a cutting edge on the tool bit- brass is easy as it needs no top rake, (which i think is called back or rear rake on your side of the pond) and you're good to go..

    Dimensions and geometry you'll have to make suit the job in hand, as 1/2" isn't much smaller than the pocket bore and you'll want the bit at an angle enough to clear the body for cutting, but also project past the tip, otherwise it won't reach the bottom of the pocket.
    You can buy them that small but probably $60-$80 upwards in your money.

Thread Information

Users Browsing this Thread

There are currently 7 users browsing this thread. (0 members and 7 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •